Machine Vision

Smart camera are vision systems that extracts information from the captured image as required by application. Smart cameras are also termed as intelligent camera is used in various complex applications.

Send Enquiry

We are very pleased to announce the new USB microscopy camera. The very high resolution 5.0 Mega pixel microscopy camera. With 2592X1944 pixels resolution, you can see much more details than before. The price of the new camera is lowest then microscopy Camera, ask your price today. At the same time, the price of 3.0 Mega pixels camera is lower than before now. You can contact our business coordinator to inquire

Sensor	1/2.5"color 5.0MP CMOS
Pixel size	2.2um x 2.2um
Resolution	2592 x 1944
Sensitivity	1.0V/lux-sec@550 nm
Read	Progress
Exposure	ERS (Electronic rolling snap)
Speed	3.3 fps @ 2592 x 1944, 15 fps @ 1280 x 960, 30fps@864 x 600
support	Direct-show interface

Fire Wire Camera

FireWire color camera
FireWire CCD camera
1/4" CCD, progressive scan
640 x 480 pixel
Up to 60 images/s
Trigger input and I/O
IEEE 1394
Protocol: DCAM 1.31

General behavior:

Video formats @ Frame rate	rate640 x 480 UYVY @ 30, 15, 7.5, 3.75 fps
Sensitivity	0. .5 lx at 1/30s, gain 20 dB
Dynamic range	ADC: 10 bit, output: 8 bit
SNRADC:	9 bit at 25 °C, gain 0 dB

Interface (optical):

Sensor specification	ICX098BQ [671.36 KB, PDF]
Type	progressive scan
Format	1/4 "
Resolution	H: 1024, V: 768Pixel
Size	H:5.6 µm, V: 5.6 µm
Lens	C/CS mount

Interface (electrical):

Supply voltage	8 to 30 VDC
Current consumption	Approx 200 mA at 12 VDC

Interface (mechanical):

Dimensions	H: 50.6 mm, W: 50.6 mm, L: 50 mm
Mass	265 g

Adjustments (man):

Shutter	1/10000 to 30 s
Gain	0 to 36 dB
Offset	0 to 511
Saturation	0 to 200 %
White balance	-2 dB to +6 dB

Adjustments (auto):

Shutter	1/10000 to 30 s
Gain	0 to 36 dB
Offset	0 to 511
Saturation	0 to 200 %
White balance	-2 dB to +6 dB

Environmental:

Max. temperature (operation)	-5 °C to 45 °C
Max. temperature (storage)	-20 °C to 60 °C
Max. humidity (operation)	80 % non-condensing
Max. humidity (storage)	95 % non-condensing
White balance	-2 dB to +6 dB

SVCam-ECO
ECO-Line CCD-Cameras
SVCam-ECO cameras support the industrial image transfer protocol of Gigabit Ethernet. Gigabit Ethernet delivers to your application absolutely new dimensions: These gige camera has following features-
-Extreme small design
-High frame rates
-Industrial standard
-Cable length up to 100m
-Budgetary cost level

SVCam-ECO cameras are available in 4 resolutions from 640 x 480 up to 1600 x 1200 pixel. These gige cameras are designed to reach high frame rates at low signal-to-noise ratios and are enclosed in an utmost small housing.

The modular concept of SVCam-cameras provides our customers with a fast and low cost way to design customized versions for application specific requirements. Unique processing of the vision CCD camera guarantees an excellent signal-to-noise ratio. The internal logic allows different ways to adjust exposure time and select trigger modes including:

-Synchronization of image capture to an external event (trigger mode)
-Free running with adjustable frame rate
-Exposure time control via Ethernet interface or over trigger pulse width
-Extend the exposure time under low light level conditions

Progressive scan technology 4 resolution options: - eco424 640 x 480 pixel - eco204 1024 x 768 pixel - eco267 1360 x 1024 pixel - eco274 1600 x 1200 pixel Synchronization: - free running (frame rate adjustable) - external trigger with internal exposure control - external trigger with pulse width exposure control - software trigger via PC Monochrome and color sensors (Bayer Pattern) with LUT (4 x) 64 MB memory inside 8/12 Bit video data stream (14 Bit ADC used) 1000 MBit Ethernet (Gigabit Ethernet) 100 T compatible Selectable AOI

Adjustable gain/auto gain Strobe output (e.g. for light flash) General purpose I/Os Time stamp capability Low offset 2 x 2 binning mode Partial scan mode for higher frame rates Standard C-Mount 10V - 30V DC; e.g. 300mA @ 12V consumption Operating temperature range: -10°C to +40°C • Temperature sensor to avoide overheating Weight approx. 160g Status LEDs Full 2 years warranty

Flea®2
Ultra-Compact + Versatile + 1394b
12 different models, 0.3 MP to 5.0 MP
Smallest 1 394b camera in the world
High speed 1394b 800 Mb/s digital interface
Metal case with locking screw connection
Ideal for industrial machine vision
With resolutions ranging from 0.3MP (VGA) to 5.0MP and 12 different models to choose from, the compact, versatile Flea®2 camera system is a complete, cost effective and reliable IEEE-1 394b solution for demanding imaging applications such as semiconductor inspection and high-speed assembly.

Specification	FL2- 03S2M/C	FL2- 08S2M/C	FL2- 14S3M/C	FL2-20S4M/C	FL2G-13S2M/C	FL2G-50S5M/C
Image Sensor Type	Sony progressive scan interline transfer CCD's with square pixels and global shutter, monochrome or color
Image Sensor Model	Sony ICX424 1/3"	SonyICX204 1/3"	Sony ICX267 1/2"	Sony ICX274 1/1.8"	ICX445 1/3" EXview HAD CCD™	ICX655 2/3" SuperHAD CCD™
Maximum Resolution	648x488	1032x776	1392x1032	1624x1224	1296x964	2448x2048
Pixel Size	7.4 x 7.4µm	4.65 x4.65µm	4.65 x4.65µm	4.4 x 4.4µm	3.75 x 3.75µm	3.45 x 3.45µm
Analog-to-Digital Converter	Analog Devices 12-bit ADC
Video Data Output	8, 12, 16 and 24-bit digital data
Image Data Formats	Y8, Y16 (all models), RGB, YUV41 1, YUV422, YUV444, 8-bit and 16-bit raw Bayer data (color models)
Digital Interface	Bilingual 9-pin IEEE-1394b for camera control, video data transmission, and power
Transfer Rates	100, 200,400, 800 M bit/s
Maximum Frame Rates	648x488 at 80 FPS1032x776 at 30 FPS1392x 1032 at 15 FPS1624x 1224 at 15 FPS1296x964 at 30 FPS2448x2048 at 7.5 FPS
Partial Image Modes	pixel binning and region of interest modes via Format_7
White Balance	automatic / manual / one-push modes, programmable via software
General Purpose I/O Ports	8-pin Hirose HR25 GPIO connector opto-isolated pins for trigger and strobe (FL2G models only), bi-directional pins for trigger, strobe or serial port
Gain	automatic / manual / one-push gain modes, programmable via software, 0dB to 24dB in 0.04dB increments
Shutter	automatic / manual / one-push modes, programmable via software, 0.02ms to greater than 10s (extended shutter mode)
Gamma/LUT	0.50 to 4.00 / programmable lookup table
Synchronization	via external trigger, software trigger, or free-running
External Trigger Modes	DCAMv1.31 Trigger Modes 0, 1, 3, 4 and 5 (multiple exposure, 03S2 and 08S2 models only), 14 (overlapped trigger), and 15 (multi-shot trigger)
Memory Storage	(FL2G models only) 32MB frame buffer, 5 12KB non-volatile data flash
Memory Channels	3 memory channels for custom camera settings
Power Requirements	power via Vext GPIO pin or 9-pin 1394b interface: 8 to 32 V, less than 2.5 W
Dimensions (L x W x H)	29mm x 29mm x 30mm (excluding lens holder, without optics)
Mass	58g (without optics)
Camera Specification	IIDC 1394-based Digital Camera Specification v 1.3 1, compatible with IEEE-1 394b and IEEE-1 394a interfaces
Lens Mount	C-mount
Emissions Compliance	Complies with CE rules and Part 15 Class A of FCC Rules
Operating Temperature	0° to 45 °C
Storage Temperature	-30° to 60°C
Warranty	2 years

.

Ring Lights (Direct Lighting)
High-density LED ring lights create an extremely bright concentration of light at the center of the illumination area. LED illumination is applicable for a wide variety of uses.

Low-angle Ring Lights (Direct Lighting)
Low-angle LED illumination is ideally suited for edge detection and for emphasizing printing, damage, etc., on metal surfaces

Bar-Lights (Direct Lighting)
High-intensity LED arrays in a rectangular oblique illumination units. The angle of the LED arrays can be adjusted independently for use in a wide range of different situations.

Ring Lights (Indirect Lighting)
Evenly diffuse top lighting. Overhead diffuse light eliminates LED glare and shadows for even illumination.

Low-angle Ring/Square Lights (Indirect Lighting)
Even, diffused side lighting. Low-angle, diffuse illumination enables characters and defects to be uniformly illuminated with no LED glare.

Dome Lights (Indirect Lighting)
Even illumination transmits light at all angles allowing an object to be evenly illuminated

Flat-Dome Lights (Indirect Lighting)
A unique pattern of dots on the light surface controls light diffusion and transmission, to achieve a highly uniform, shadow-less diffused light pattern for typical dome light applications, but in a much smaller package and lower cost.

Back Lights (Indirect Lighting)
Power saving back light system with a very thin design and a very uniform surface light emission profile

Coaxial Lights (Indirect Lighting)
Bright, even illumination across the entire field of view makes on-axis illumination systems ideally suited for inspecting mirror-finish objects for scratches etc.

Machine vision system is a PC-based vision systems for accurate & complex reading as well as measurement applications. These systems are ideal for applications that require multiple cameras or color image analysis and are widely used in electronic components, medical devices, automotive parts, disposable consumer goods, packaging and pharmaceutical. These applications does not require much knowledge of programming & machine vision to configure vision applications and can be developed in a graphical point-and-click environment.

Vision reader plus : Vision reader plus enables to set up a typical application by specifying a search area, adjusting some parameters for extraction of the symbols and selecting an appropriate OCR font. It is widely used for bar code reading and can read bar code as well as data code at any angle & any position inside image. If the syntax of the words that must be read is known or they match the entries of a dictionary, the results of reader plus will be displayed.

Measure plus : Measure plus is used to find out geometrical measurement of parts like length, radius, angles etc. with high accuracy. It is used to color applications, to monitor color on products and is perfect for automotive and packaging industries. All the measurement values can be collected into excel sheet.

MVP Match-it : Our MVP match-it is a vision solution for all the industries where matching pattern is used. It is easy to use and useful to match features of parts like assembly presence / absence, object matching etc. This software for machine vision application does not require programming knowledge and is available at highly competitive prices.

Machine Vision Plus is the leading supplier of optics, opto-mechanical sub-assemblies and opto-electronic system solutions for machine vision, automation, assembly, imaging, testing, measuring, and inspection. Our optical designs are involved in applications such as semiconductor metrology, electronic imaging, telecommunications, biometrics, photonics R&D, non-contact measurement, and biotechnology and life science.